Mackie TT24 Manuel du propriétaire télécharger pdf (Page 19)

Owner’s Manual

3.7 Group and Master Controls

The TT24 has four Group strips and one Master strip

(Figure 3-8). Each Group has a V-Pot to control group

pan and the Group Mode, MUTE, SELECT, SOLO but-

tons, and a fader. The four Group strips control either

Groups 1–4 or 5–8. The currently selected Group bank is

indicated by the lit GROUP ASSIGN/SELECT buttons.

3.7.1 Changing the Group Bank

Press any of the GROUP ASSIGN/SELECT buttons to

select that Group bank. The GROUP ASSIGN/SELECT

buttons illuminate 1–4 or 5–8 and cause the faders and

buttons to snap to their previous Group bank settings.

3.7.2 Group Assignment

Press and hold a GROUP ASSIGN/SELECT button

and press the channel SELECT buttons to add/subtract

channels from that Group. This method is used for all of

the GROUP ASSIGN/SELECT buttons: Groups 1–8, L/R

and CTR/Mono.

The SELECT button for channels assigned to a

group light when a GROUP ASSIGN/SELECT button

is held down.

A selected channel can also be assigned to groups by

selecting GRP/AUX in the QuickMix area to view the

Group/Aux parameters on the Touchscreen.

3.7.3 Group Parameter Control

Press a GROUP SELECT button to access that

Group’s settings and controls from the QuickMix section

just like an input channel.

3.7.4 Mute Groups

Eight dedicated mute groups are available for applica-

tions where muting groups of input channels quickly

with a single button is required. All channels from the

ANLG, DGTL, and RTNS bank can be included in a mute

group. Outputs are not available for mute groups.

The Mute groups on the TT24 use the group assign

area of the mixer’s control surface to assign channels to a

mute group as well as to activate/deactivate mute groups.

To assign input channels to a Mute Group:

Press and hold the CTRL button in the QuickMix area

and also press any one of the GROUP ASSIGN 1-8

buttons. When this is done, the Group Assign button il-

luminates and the Group Mute button blinks, indicating

the TT24 is in Mute Group Assign mode. Simply press

the channel mute button for any input to be included

in the Mute Group. You can press other Group Assign

buttons to congure any of the eight mute groups when

in this assign mode. Pressing the blinking Mute Group

MUTE button or lit Group Assign button will exit the

assignment mode.

To activate/deactivate Mute Groups:

Press the Group Mute button while holding the Group

Assign button to activate and deactivate mute groups.

All channel mutes will light when a mute group is suc-

cessfully activated.

Note: TT24 Mute Groups are unlike those on an

analog console in that they are destructive. When a

Mute Group is engaged, you can unmute an individual

channel with the channel mute button. This allows for

easier muting of groups and individual channels.

3.8 Solo Area

The Solo area (Figure 3-9) has two buttons: CLEAR

SOLO and PFL.

Figure 3-9 Solo area

V-P

NTR

PFL

PAN

HPF

LEA

TRIM

METER

Clear Solo PFL

3.8.1 CLEAR SOLO

Press this momentary button to clear any soloed chan-

nels. It lights yellow when any solo buttons are active as

does the RUDE SOLO LED (Figure 3-5).

3.8.2 PFL

Activate this yellow backlit button so all soloed chan-

nels are PFL (pre-fader listen). Solo selections are AFL

(after-fader listen) when the button is not lit.

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 67 68

Commentaires sur ces manuels

Pas de commentaire

Mackie TT24 Manuel du propriétaire Page 19

Commentaires sur ces manuels

Produits connexes et manuels pour Contrôleurs de DJ Mackie TT24